View XREGRN-L1-0000-00P01_8028564.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

cld-ds05 rev 15 e product family data sheet cree ? xlamp ? xr-e led product description the xlamp xr- e le d is leading the l e d lighting revolution with its unprecedented lighting-class brightness, effcacy, lifetime and quality of light. these lighting-class features enable the xlamp xr- e led to replace many traditional light sources and save money with energy-effcient light and long lifetimes. cree xlamp l e ds bring high performance and quality of light to a wide range of lighting applications, including color-changing lighting, portable and personal lighting, outdoor lighting, indoor directional lighting, commercial lighting and emergency-vehicle lighting. features ? available in white (2600 k to 10,000 k cct), blue, royal blue and green ? maximum drive current: up to 1000 ma ? maximum junction temperature: 150 c ? industry-leading jedec standard pre-qualifcation testing ? refow solderable C jedec j-std-020c compatible ? electrically neutral thermal path ? rohs- and r each-compliant ? ul-recognized component (e349212) www. cree.com/xlamp copyright ? 2006-2013 cree, inc. a ll rights reserved. the information in this document is subject to change without notice. cree ? , the cree logo and xlamp ? are registered trademarks of cree, inc. cree, inc. 4600 silicon drive durham, nc 27703 us a tel: +1.919.313.5300 table of contents characteristics .............................. 2 flux characteristics - white ............ 3 flux characteristics - color ............. 4 relative spectral p ower distribution . 5 relative flux vs. junction temperature ................................. 6 e lectrical characteristics ................. 7 relative flux vs. current ................ 7 typical spatial distribution .............. 8 thermal design ............................. 8 refow soldering characteristics ...... 9 notes .......................................... 10 mechanical dimensions .................. 12 tape and reel ............................... 13 dry p ackaging and p ackaging ......... 14
2 characteristics characteristics unit minimum typical maximum thermal resistance, junction to solder point c/w 8 viewing angle (fwhm) - white degrees 90 viewing angle (fwhm ) - royal blue, blue, green degrees 100 temperature coeffcient of voltage - white, royal blue, blue, green mv/c -4.0 esd classifcation (hbm per m il-std-883d) class 2 dc forward current - white 5000 k, royal blue, blue ma 1000 dc forward current - white < 5000 k, green ma 700 dc p ulse current (@ 1 khz, 10% duty cycle) a 1.8 reverse v oltage v 5 forward voltage (@ 350 m a) v 3.3 3.9 forward voltage (@ 700 m a) v 3.5 forward voltage (@ 1000 m a ) - white 5000 k, royal blue, blue v 3.7 led junction temperature c 150 copyright ? 2006-2013 cree, inc. all rights reserved. the information in this document is subject to change without notice. cree ? , the cree logo and xlamp ? are registered trademarks of cree, inc. xlamp xr-e leds
3 flux characteristics (t j = 25 c) - white the following tables describe the available colors and fux for xr-e leds by listing the correlated color temperature or dominant wavelength range for the entire family and by providing several base order codes. it is important to note that the base order codes listed here are a subset of the total available order codes for the product family. for more order codes, as well as a complete description of the order-code nomenclature, please consult the xr family binning and labeling document. color cct range base order codes min. luminous flux order code min. max. group flux (lm) cool white 5000 k 10,000 k p4 80.6 xre wht-l1-0000-00901 q2 87.4 xre wht-l1-0000-00a01 q3 93.9 xrew ht-l1-0000-00b01 q4 100 xre wht-l1-0000-00c01 q5 107 xre wht-l1-0000-00d01 r2 114 xre wht-l1-0000-00e01 neutral white 3700 k 5000 k p3 73.9 xre wht-l1-0000-008e4 p4 80.6 xre wht-l1-0000-009e4 q2 87.4 xre wht-l1-0000-00ae4 q3 93.9 xrew ht-l1-0000-00be4 q4 100 xre wht-l1-0000-00ce4 warm white 2600 k 3700 k n3 56.8 xre wht-l1-0000-005e7 n4 62.0 xre wht-l1-0000-006e7 p2 67.2 xre wht-l1-0000-007e7 p3 73.9 xre wht-l1-0000-008e7 p4 80.6 xre wht-l1-0000-009e7 notes: ? cree maintains a tolerance of 7% on fux and power measurements , 0.005 on chromaticity (ccx, ccy) measurements and 2 on cri measurements. ? typical cri for cool w hite & neutral white (3700 k C 10,000 k cct) is 75. ? typical cri for w arm white (2600 k C 3700 k cct) is 80. copyright ? 2006-2013 cree, inc. all rights reserved. the information in this document is subject to change without notice. cree ? , the cree logo and xlamp ? are registered trademarks of cree, inc. xlamp xr-e leds
4 flux characteristics (t j = 25 c) - color the following tables describe the available colors and fux for xr-e leds by listing the correlated color temperature or dominant wavelength range for the entire family and by providing several base order codes. it is important to note that the base order codes listed here are a subset of the total available order codes for the product family. for more order codes, as well as a complete description of the order-code nomenclature, please consult the xr family binning and labeling document. color dominant wavelength range base order c odes min radiant flux (mw) order code min. max. group dwl (nm) group dwl (nm) group flux (mw) royal blue d3 450 d5 465 13 300 xrero y-l1-0000-00801 14 350 xrero y-l1-0000-00901 15 425 xrero y-l1-0000-00 a01 color dominant wavelength range base order codes min luminous flux (lm) order code min. max. group dwl (nm) group dwl (nm) group flux (lm) blue b3 465 b6 485 j 23.5 xreblu-l1-0000-00j01 k 30.6 xreblu-l1-0000-00k01 color dominant wavelength range base order c odes min. luminous flux (lm) order code min. max. group dwl (nm) group dwl (nm) group flux (lm) green g2 520 g4 535 p 67.2 XREGRN-L1-0000-00P01 note: cree maintains a tolerance of 7% on fux and power measurements and 1 nm on dominant wavelength measurements. copyright ? 2006-2013 cree, inc. all rights reserved. the information in this document is subject to change without notice. cree ? , the cree logo and xlamp ? are registered trademarks of cree, inc. xlamp xr-e leds
5 relative spectral power distribution relative spectral power 0 20 40 60 80 100 400 450 500 550 600 650 700 750 relative radiant power (%) wavelength (nm) 5000k - 10000k cct 3700k - 5000k cct 2600k - 3700k cct 0 20 40 60 80 100 400 450 500 550 600 650 relative radiant power (%) wavelength (nm) royal blue blue green copyright ? 2006-2013 cree, inc. all rights reserved. the information in this document is subject to change without notice. cree ? , the cree logo and xlamp ? are registered trademarks of cree, inc. xlamp xr-e leds
6 relative flux vs. junction temperature (i f = 350 ma) relative flux output vs. junction temperature 0% 10% 20% 30% 40% 50% 60% 70% 80% 90% 100% 25 50 75 100 125 150 relative luminous flux junction temperature ( c) white blue green electrical characteristics (tj = 25oc) 0% 10% 20% 30% 40% 50% 60% 70% 80% 90% 100% 25 50 75 100 125 150 relative radiant flux junction temperature (oc) royal blue copyright ? 2006-2013 cree, inc. all rights reserved. the information in this document is subject to change without notice. cree ? , the cree logo and xlamp ? are registered trademarks of cree, inc. xlamp xr-e leds
7 electrical characteristics (t j = 25 ?c) relative flux vs. current (t j = 25 ?c) thermal design 0 100 200 300 400 500 600 700 800 900 1000 0.0 1.0 2.0 3.0 4.0 5.0 forward current (ma) forward voltage (v) typical spatial radiation pattern 0 50 100 150 200 250 0 200 400 600 800 1000 relative luminous flux (%) forward current (ma) green white, royal blue & blue copyright ? 2006-2013 cree, inc. all rights reserved. the information in this document is subject to change without notice. cree ? , the cree logo and xlamp ? are registered trademarks of cree, inc. xlamp xr-e leds
8 typical spatial distribution thermal design 0 20 40 60 80 100 120 - 100 - 80 - 60 - 40 - 20 0 20 40 60 80 100 relative luminous intensity (%) angle ( ) white royal blue, blue & green neutral white, warm white & green neutral white, warm white, blue, royal blue and green relative intensity vs. current (tj = 25oc) 0 100 200 300 400 500 600 700 800 0 25 50 75 100 125 150 maximum current (ma) ambient temperature ( c) rj - a = 10 c/w rj - a = 15 c/w rj - a = 25 c/w rj - a = 35 c/w thermal design cool white, royal blue & blue cool white 0 200 400 600 800 1000 1200 0 25 50 75 100 125 150 maximum current (ma) ambient temperature ( c) rj - a = 10 c/w rj - a = 15 c/w rj - a = 20 c/w rj - a = 25 c/w copyright ? 2006-2013 cree, inc. all rights reserved. the information in this document is subject to change without notice. cree ? , the cree logo and xlamp ? are registered trademarks of cree, inc. xlamp xr-e leds
9 reflow soldering characteristics in testing, cree has found xlamp xr-e leds to be compatible with jedec j-std-020c, using the parameters listed below. a s a general guideline, cree recommends that users follow the recommended soldering profle provided by the manufacturer of solder paste used. note that this general guideline may not apply to all p cb designs and confgurations of refow soldering equipment. profle feature lead-based solder lead-free solder average ramp-up rate (ts max to tp) 3 c/second max. 3 c/second max. p reheat: temperature m in (ts min ) 100 c 150 c p reheat: temperature m ax (ts max ) 150 c 200 c preheat: time (ts min to ts max ) 60-120 seconds 60-180 seconds time maintained above: temperature (t l ) 183 c 217 c time maintained above: time (t l ) 60-150 seconds 60-150 seconds p eak/classifcation temperature (tp) 215 c 260 c time within 5 c of actual p eak temperature (tp) 10-30 seconds 20-40 seconds ramp-down rate 6 c/second max. 6 c/second max. time 25 c to p eak temperature 6 minutes max. 8 minutes max. note: a ll temperatures refer to topside of the package, measured on the package body surface. copyright ? 2006-2013 cree, inc. all rights reserved. the information in this document is subject to change without notice. cree ? , the cree logo and xlamp ? are registered trademarks of cree, inc. xlamp xr-e leds
10 notes lumen maintenance projections cree now uses standardized i e s lm-80-08 and tm-21-11 methods for collecting long-term data and extrapolating led lumen maintenance. for information on the specifc l m -80 data sets available for this led, refer to the public lm-80 results document at www.cree.com/xlamp_app_notes/l m80_results. p lease read the xlamp long-term lumen m aintenance application note at www.cree.com/xlamp_app_notes/lumen_ maintenance for more details on crees lumen maintenance testing and forecasting. p lease read the xlamp thermal m anagement application note at www.cree.com/xlamp_app_notes/thermal_management for details on how thermal design, ambient temperature, and drive current affect the led junction temperature. moisture sensitivity xlamp leds are shipped in sealed, moisture-barrier bags ( m bb) designed for long shelf life. if xlamp leds are exposed to moist environments after opening the m bb packaging but before soldering, damage to the led may occur during the soldering operation. the following derating table defnes the maximum exposure time (in days) for an xlamp led in the listed humidity and temperature conditions. leds with exposure time longer than the time specifed below must be baked according to the baking conditions listed below. cree recommends keeping xlamp leds in their sealed moisture-barrier packaging until immediately prior to use. cree also recommends returning any unused leds to the resealable moisture-barrier bag and closing the bag immediately after use. temp. maximum percent relative humidity 30% 40% 50% 60% 70% 80% 90% 30 oc 9 5 4 3 1 1 1 25 oc 12 7 5 4 2 1 1 20 oc 17 9 7 6 2 2 1 baking conditions it is not necessary to bake all xlamp leds. only the leds that meet all of the following criteria must be bak ed: 1. leds that have been removed from the original mbb packaging. 2. leds that have been exposed to a humid environment longer than listed in the m oisture sensitivity section above. 3. leds that ha ve not been soldered. leds should be baked at 80 oc for 24 hours. leds may be baked on the original reels. remove leds from m bb packaging before baking. do not bake parts at temperatures higher than 80 oc. this baking operation resets the exposure time as defned in the m oisture sensitivity section above. copyright ? 2006-2013 cree, inc. all rights reserved. the information in this document is subject to change without notice. cree ? , the cree logo and xlamp ? are registered trademarks of cree, inc. xlamp xr-e leds
11 storage conditions xlamp leds that have been removed from original m bb packaging but not soldered yet should be stored in a room or cabinet that will maintain an atmosphere of 25 5 oc and no greater than 10% rh (relative humidity). for leds stored in these conditions, storage time does not add to exposure time as defned in the m oisture sensitivity section above. rohs compliance the levels of rohs restricted materials in this product are below the maximum concentration values (also referred to as the threshold limits) permitted for such substances, or are used in an exempted application, in accordance with eu directive 2011/65/ec (rohs2), as implemented january 2, 2013. rohs declarations for this product can be obtained from your cree representative or from the p roduct documentation sections of www.cree.com. reac h c ompliance rea ch substances of high concern (svhcs) information is available for this product. since the european chemical a gency (echa ) has published notice of their intent to frequently revise the svhc listing for the foreseeable future, please contact a cree representative to insure you get the most up-to-date svhc declaration. re a ch banned substance information (reach a rticle 67) is also available upon request. vision advisory claim wa rning: do not look at exposed lamp in operation. eye injury can result. see led eye safety at www.cree.com/ xlamp_app_notes/led_eye_safety. copyright ? 2006-2013 cree, inc. all rights reserved. the information in this document is subject to change without notice. cree ? , the cree logo and xlamp ? are registered trademarks of cree, inc. xlamp xr-e leds
12 mechanical dimensions (t a = 25 c) all measurements are .1mm unless otherwise indicated. lens re flector substr ate lens re flector substr ate 8.4 mm 5.6 mm 0.7 mm 9.0 mm 7.0 mm 6.46 mm 6.8 mm 4.4 .2 mm 7.0 mm 5.6 mm 0.70 mm 8.4 mm 6.46 mm side vie w t op view bottom view re commended pc board solder p ad anode anode 7.0 mm 5.6 mm 0.70 mm 8.4 mm 6.46 mm re commended pc board solder pa d 6.36 8.30 0.60 0.80 0.80 0.60 5.50 7.10 recommended stencil pattern 7090 (hatched area is opening) recommended solder pad for xlamp xr family leds recommended stencil pattern for xlamp xr family leds (hatched area is opening) copyright ? 2006-2013 cree, inc. all rights reserved. the information in this document is subject to change without notice. cree ? , the cree logo and xlamp ? are registered trademarks of cree, inc. xlamp xr-e leds
13 tape and reel all cree carrier tapes conform to eia -481d, a utomated component handling systems standard. all dimensions in mm. 12.0.1 5.5.1 13.5 (min) 16.0 +.3 -.0 1.75.10 4.0.1 50 empty pockets with tape 60 (min) empty pockets with tape 5-10 empty pocktes with unsealed cover tape 1.5 .1 anode side cathode side loaded pockets user feed direction start 12.0.1 5.5.1 13.5 (min) 16.0 +.3 -.0 1.75.10 4.0.1 50 empty pockets with tape 60 (min) empty pockets with tape 5-10 empty pocktes with unsealed cover tape 1.5 .1 anode side cathode side loaded pockets user feed direction start 330.2 mm + copyright ? 2006-2013 cree, inc. all rights reserved. the information in this document is subject to change without notice. cree ? , the cree logo and xlamp ? are registered trademarks of cree, inc. xlamp xr-e leds
14 dry packaging and packaging label with cree bin code, qty, lot # label with cree bin code, qty, lot # vacuum-sealed moisture barrier bag dessicant (inside bag) humidity indicator card (inside bag) patent label label with customer order code, qty, reel id, po # patent label label with cree bin code, qty, reel id humidity indicator card (inside bag) dessicant (inside bag) label with cree bin code, qty, reel id label with cree order code, qty, reel id, po # label with cree order code, qty, reel id, po # label with cree bin code, qty, reel id unpackaged reel packaged reel boxed reel copyright ? 2006-2013 cree, inc. all rights reserved. the information in this document is subject to change without notice. cree ? , the cree logo and xlamp ? are registered trademarks of cree, inc. xlamp xr-e leds

▲Up To Search▲

Price & Availability of XREGRN-L1-0000-00P01

	To Download XREGRN-L1-0000-00P01 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .